What about walls and light reflection ?

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Choosing the right surface for the walls of your grow room is very important, as up to 40% of your total yield comes from the edge, and the right wall surface can increase the amount of light those plants receive by up to 30%! Artificial lighting diminishes exponentially with distance, so it is important to contain as much of this light as possible, and direct it accordingly. Reflective surfaces also help illuminate the lower portions of the garden, providing lower buds with light and heat energy.

To get the best results with your light and walls, it is important to get the walls as close as possible to your garden to ensure the least amount of light is wasted. As a caveat, the percentages provided are only useful as a general guideline, as they present the range of reflectivity of the particular surfaces. The high percentage presents the best possible circumstances for that material (for example a 99% reflectivity rating for mylar sheeting would be under ideal conditions - no creases, completely flat, no discoloration, etc).

The best way to determine how well your grow room walls reflect light would be to purchase a light meter and measure your light directly; then take an opaque board and hold it a few inches off one of your walls with the light meter below the board in such a fashion that the light reflects off the wall and onto the light meter. You can then compare the difference between the two and determine a percentage from those numbers, the closer the two numbers are, the better your wall reflects light. It is important that in both measurements, your light meter is the same distance from the light, otherwise your results will be skewed.

Also important to note is that radiant light energy refers to electromagnetic (EM) radiation with a wavelength between 400-700 nanometers (nm) and radiant heat energy correlates to EM radiation with a wavelength between 800-2000nm.

Listed below are some of the most commonly used materials used for grow room walls:


t_foylon.jpg

Foylon:


A more durable version of mylar, made of spun polyester fabric and reinforced with foil laminate. Foylon is resistant to most solutions, won't tear or fade, and can be wiped or washed clean.

A great solution for growers who are interested in long term use, and though it may be slightly more expensive than mylar, its durability will more than make up for its cost. It has the ability to reflect about 95% of the light and approximately 85% of the heat energy, so a good ventilation system should be used in conjunction with folyon.

A recommended method to attach Foylon to the walls would be using Velcro, as it makes taking it down for cleaning much easier nd reduces the risk of tearing, creasing or bending it. If this is used for your walls, making sure you get it flush with the wall with no pockets of air between it and the wall to prevent hotspots.


t_mylar.jpg

Mylar:


A highly reflective polyester film that comes in varying thickness, the most common being 1 and 2 mm thick. The 2mm thick mylar while not quite as durable as the foylon, is fairly rugged. The 1mm thick mylar tears fairly easily, so taking it down for cleaning is quite difficult without damaging it in the process. Both types of mylar are able to reflect approximately 92-97% reflective, giving it the potential to be more reflective than foylon, but because foylon is more easily cleaned without damaging it as well as it being harder to crease, foylon usually ends up being slightly more reflective. Important to note is that mylar reflects radiant heat energy just as well as foylon (around 85%), so proper ventilation is necessary if mylar is used in your grow room. Attaching this to walls can be done in a similar fashion as foylon, and the same caution should be used to avoid creating hotspots in your room. The 1mm thick mylar stands a fair chance of being creased or ripped in the process unfortunately, even if Velcro is used to attach to the walls.

C3 anti-detection film:

A specialized type of mylar that exhibits the same properties as the 2mm thick mylar, but in addition to reflecting approximately 92-97% of the light, it also is 90% infrared proof, making your grow room all but invisible to IR scanning. This can also be attached in the same manner as foylon or mylar, and the same caution should be used to avoid creating hotspots in your room.

Flat white paint:

Self explanatory; a great option for large grow rooms or for people who are interested in a low maintenance wall. Flat white paint has the ability to reflect between 75-85% of the light, and does not create hotspots. Adding a fungicide is recommended when painting.

Glossy and eggshell whites do not reflect light as efficiently as flat white. Semi-gloss paint for example, only has the ability to reflect between 55-60% of the light. Also important to remember when using paint is that any smears or blemishes on the surface take away from how reflective the wall is so care should be taken to avoid marking or staining the walls. Titanium white paint is very reflective; however it is usually only used on reflectors due to its high cost.


White/Black plastic (also known as panda plastic or "poly"):

"Poly" is useful if you are setting up a temporary grow room or dont want to damage the walls. Poly is easily cleaned.

The purpose of the black side is to not allow any light to pass through the plastic, which ensures your dark cycle remains dark. The white side is 75-90% reflective. Choose a 6 "mill" thickness of poly for maximum light blockage and duribility.

If this plastic is put too close to the light, you will obviously melt it so be careful!. Panda plastic does not create hotspots. Poly can be attached to the walls by using carpenters nails or using tape glue or similar means. This can be used as a cheap alternative to mylar if painting your grow room is out of the question.

Polystyrene Foam Sheeting (more commonly known as Styrofoam):

This is excellent for harsh environment growrooms (your attic for example), provided you have a good ventilation system and a way to keep the temperatures from rising too high (an a/c unit or similar) as it is an excellent insulator.

It is also a great material for use in a temporary setup or for use as a "travelling reflector" on a light mover, where weight is a concern. It is approximately 75-85% light reflective so it is comparable to using a flat white paint. Foam will not create hot spots. Rigid foam can be purchased in sheets, and can be used as a free standing wall or can be taped, glued or nailed to the wall, the last generally being the most successful method.


t_emergency-blanket.JPG

Emergency Blankets:


These are ultra thin polyester blankets that are sold in most camping stores and are constructed of a single layer of polyester film that is covered with a layer of vapor deposited aluminum.

It is not very effective at reflecting light because it is so thin. Holding it between you and a light source, many small holes are noticed at the intersections of creases and the entire blanket is translucent to begin with, this coupled with the many creases that are in it when you purchase it takes away a significant amount of it reflectivity. It is very easily creased as well which also detracts from its ability to reflect light. And while it is reflects nearly 90% of radiant heat energy, it is only able to reflect around 70% of the light.

The largest advantage of using this type of material is that it is very cheap and therefore easily replaced. Emergency blankets can create hotspots if not attached flush to the wall so it is important that no air gaps exist between it and your supporting wall. The easiest way to attach this is to use tape (Aluminum or metal tape is recommended), as it tears very easily once it is cut or punctured.

Aluminum Foil:

Aluminum foil is no more than 55% reflective - if used, make sure that the dull side is the one that is used to reflect the light. When it becomes creased its reflectivity is even lower (around 35%.) It is also very dangerous to use because it creates hotspots easily, is electrically conductive, and is a fire hazard when it is in close contact with HID lighting. Attaching this to walls is a pain and usually using aluminum tape or glue is the best way. This should only be used as a last resort, and even then its usefulness is questionable.
 
Agree. As you add more light, plant uptakes more nutes....to a point. It requires quite a bit of science. This is a high end game, with breeding specifically for this end. It requires tons of info on the chosen strains ability to uptake nutes to keep up with light available. Strain specific nute requirements, as well as maximum par for that strain, and maximum Nute uptake. Once you are at that point, and know the maximum amount of light that correlates to maximum nute uptake, CO2 can allow a little more light than the plants can to normally deal with. Most hobby grows are nowhere even close to sciences out making it a crap shoot in my opinion. But we all no about opinions....

Bubba
On Point as always
 
Choosing the right surface for the walls of your grow room is very important, as up to 40% of your total yield comes from the edge, and the right wall surface can increase the amount of light those plants receive by up to 30%! Artificial lighting diminishes exponentially with distance, so it is important to contain as much of this light as possible, and direct it accordingly. Reflective surfaces also help illuminate the lower portions of the garden, providing lower buds with light and heat energy.

To get the best results with your light and walls, it is important to get the walls as close as possible to your garden to ensure the least amount of light is wasted. As a caveat, the percentages provided are only useful as a general guideline, as they present the range of reflectivity of the particular surfaces. The high percentage presents the best possible circumstances for that material (for example a 99% reflectivity rating for mylar sheeting would be under ideal conditions - no creases, completely flat, no discoloration, etc).

The best way to determine how well your grow room walls reflect light would be to purchase a light meter and measure your light directly; then take an opaque board and hold it a few inches off one of your walls with the light meter below the board in such a fashion that the light reflects off the wall and onto the light meter. You can then compare the difference between the two and determine a percentage from those numbers, the closer the two numbers are, the better your wall reflects light. It is important that in both measurements, your light meter is the same distance from the light, otherwise your results will be skewed.

Also important to note is that radiant light energy refers to electromagnetic (EM) radiation with a wavelength between 400-700 nanometers (nm) and radiant heat energy correlates to EM radiation with a wavelength between 800-2000nm.

Listed below are some of the most commonly used materials used for grow room walls:


t_foylon.jpg

Foylon:


A more durable version of mylar, made of spun polyester fabric and reinforced with foil laminate. Foylon is resistant to most solutions, won't tear or fade, and can be wiped or washed clean.

A great solution for growers who are interested in long term use, and though it may be slightly more expensive than mylar, its durability will more than make up for its cost. It has the ability to reflect about 95% of the light and approximately 85% of the heat energy, so a good ventilation system should be used in conjunction with folyon.

A recommended method to attach Foylon to the walls would be using Velcro, as it makes taking it down for cleaning much easier nd reduces the risk of tearing, creasing or bending it. If this is used for your walls, making sure you get it flush with the wall with no pockets of air between it and the wall to prevent hotspots.


t_mylar.jpg

Mylar:


A highly reflective polyester film that comes in varying thickness, the most common being 1 and 2 mm thick. The 2mm thick mylar while not quite as durable as the foylon, is fairly rugged. The 1mm thick mylar tears fairly easily, so taking it down for cleaning is quite difficult without damaging it in the process. Both types of mylar are able to reflect approximately 92-97% reflective, giving it the potential to be more reflective than foylon, but because foylon is more easily cleaned without damaging it as well as it being harder to crease, foylon usually ends up being slightly more reflective. Important to note is that mylar reflects radiant heat energy just as well as foylon (around 85%), so proper ventilation is necessary if mylar is used in your grow room. Attaching this to walls can be done in a similar fashion as foylon, and the same caution should be used to avoid creating hotspots in your room. The 1mm thick mylar stands a fair chance of being creased or ripped in the process unfortunately, even if Velcro is used to attach to the walls.

C3 anti-detection film:

A specialized type of mylar that exhibits the same properties as the 2mm thick mylar, but in addition to reflecting approximately 92-97% of the light, it also is 90% infrared proof, making your grow room all but invisible to IR scanning. This can also be attached in the same manner as foylon or mylar, and the same caution should be used to avoid creating hotspots in your room.

Flat white paint:

Self explanatory; a great option for large grow rooms or for people who are interested in a low maintenance wall. Flat white paint has the ability to reflect between 75-85% of the light, and does not create hotspots. Adding a fungicide is recommended when painting.

Glossy and eggshell whites do not reflect light as efficiently as flat white. Semi-gloss paint for example, only has the ability to reflect between 55-60% of the light. Also important to remember when using paint is that any smears or blemishes on the surface take away from how reflective the wall is so care should be taken to avoid marking or staining the walls. Titanium white paint is very reflective; however it is usually only used on reflectors due to its high cost.


White/Black plastic (also known as panda plastic or "poly"):

"Poly" is useful if you are setting up a temporary grow room or dont want to damage the walls. Poly is easily cleaned.

The purpose of the black side is to not allow any light to pass through the plastic, which ensures your dark cycle remains dark. The white side is 75-90% reflective. Choose a 6 "mill" thickness of poly for maximum light blockage and duribility.

If this plastic is put too close to the light, you will obviously melt it so be careful!. Panda plastic does not create hotspots. Poly can be attached to the walls by using carpenters nails or using tape glue or similar means. This can be used as a cheap alternative to mylar if painting your grow room is out of the question.

Polystyrene Foam Sheeting (more commonly known as Styrofoam):

This is excellent for harsh environment growrooms (your attic for example), provided you have a good ventilation system and a way to keep the temperatures from rising too high (an a/c unit or similar) as it is an excellent insulator.

It is also a great material for use in a temporary setup or for use as a "travelling reflector" on a light mover, where weight is a concern. It is approximately 75-85% light reflective so it is comparable to using a flat white paint. Foam will not create hot spots. Rigid foam can be purchased in sheets, and can be used as a free standing wall or can be taped, glued or nailed to the wall, the last generally being the most successful method.


t_emergency-blanket.JPG

Emergency Blankets:


These are ultra thin polyester blankets that are sold in most camping stores and are constructed of a single layer of polyester film that is covered with a layer of vapor deposited aluminum.

It is not very effective at reflecting light because it is so thin. Holding it between you and a light source, many small holes are noticed at the intersections of creases and the entire blanket is translucent to begin with, this coupled with the many creases that are in it when you purchase it takes away a significant amount of it reflectivity. It is very easily creased as well which also detracts from its ability to reflect light. And while it is reflects nearly 90% of radiant heat energy, it is only able to reflect around 70% of the light.

The largest advantage of using this type of material is that it is very cheap and therefore easily replaced. Emergency blankets can create hotspots if not attached flush to the wall so it is important that no air gaps exist between it and your supporting wall. The easiest way to attach this is to use tape (Aluminum or metal tape is recommended), as it tears very easily once it is cut or punctured.

Aluminum Foil:

Aluminum foil is no more than 55% reflective - if used, make sure that the dull side is the one that is used to reflect the light. When it becomes creased its reflectivity is even lower (around 35%.) It is also very dangerous to use because it creates hotspots easily, is electrically conductive, and is a fire hazard when it is in close contact with HID lighting. Attaching this to walls is a pain and usually using aluminum tape or glue is the best way. This should only be used as a last resort, and even then its usefulness is questionable.





to quote Unca , outfargging standing!
 
I don't understand what is going on. Cuda, you ask questions but you don't want answers? What is the point. Why don't you try and be a useful member rather than doing what ever it is you are trying to accomplish.

Maybe if you would put some effort to be a productive member you might like it rather than a rouge troll with no future here or anywhere for that matter.
 
He will not except that answer Big 😂😂😂
I’m sorry. I’ve given you all more credit than cult ideology. Meaning academia as the cult, with many branches. This also pertains to studies, which are purposely very limited to create a standard. I fought to change this within academia, and yet to no avail. Every system has their control mechanisms, elite systems that pervert for profit and control. Science itself seldom leaves the status quo control. Rethink, thinking. Trust no source, no matter the power or general consensus behind it. Proving that god exists, ( for example ), the cult member will always revert to cult ideology as proof. All systems must function like this in order for those who control it too remain in control of the system. So, by all means, go down the rabbit hole to gain a basic understanding, but always seek light, exit the rabbit hole to gain proper perspective, then rethink everything,…again, and again. Utilizing a system that simply works is mere mimicry. Wisdom is merely the best possible perspective of any given subject, at any given time. Question absolutely everything, especially yourself. Now, I started growing over 4 decades ago, and have grown hundreds of acres of weed. This is not a new subject for me. Getting back into it after a couple of decades, indoor, hydroponically, is all I’m doing. I think at least one of you has broken the dealers golden rule. Never become your own best customer. Mr. Texas sounds deep into this issue. The problem with the internet, you never know who’s on the other end ? I wasn’t really asking questions, merely information gathering of general consensus. This can help give direction to future experimentation. I’m very comfortable in the lab. I supervised, and was lead operator over 71 different environmental management facilities. Like I stated, you never know just who you’re conversing with on the internet. Most follow rabbit holes believing themselves all-knowing. Know this,….no matter the time period, humans always believe themselves on the precipice of all knowing. The very first mistake that all weak minds make. I really don’t need this site. I just thought there might be some intelligent people here. I may have been wrong ? Trial and error teaches much. Not failing teaches little more than systematic behavior.
 
It's OK. If you continue thinking about it in earnest, it will come to you.



Bubba
I do not need anyone’s consensus, no consoling. I will test on my own, and never take the simpleminded path, yet simplify the complex for big picture understanding, leading to wisdom, and/or wise decisions. I can just as easily look up any study. Getting boots on the ground experience can be beneficial. The curious layman pushes boundaries that science dare not touch. Understand academia. Most do not.
 
Gaining academic knowledge, then rising beyond the systematic cult thought is key. Becoming an autodidact. Anyone can follow a system, or path cut for all to follow. It takes much more to go beyond this.
 
But, it seems you don't play well with others. If you are so smart. Keep talking
I’m a true, rare, Sigma personality. This is true. However, those who feel threatened by this often react badly because they do not understand my thinking, nor do they have the ability. I understand this.
Fame and fortune is a gilded cage of your own creation. I seek, only too give, not to gain in pomposity, nor wealth or fame. Most cannot understand this thinking either. Greed has been well instilled in the slave populous. This is not my ego, but lack there of, intentionally. I seek enough ongoing information too position myself as to teach others better to fish and provide for themselves. This gives me self worth. However, when attacked, an alpha will find themselves out-alpha’ed. I have that ability, but I hate having to do it. I do “ group “ very briefly in general. Only long enough generally to touch base, help where needed, then back to solitude. I’m a giver, not a taker, but will bring down tyrants, as to free the masses. Be free to seek understanding between the lines of what I’ve written, and if you do not understand “ Sigma “, there are many videos on YouTube that try to get it right. It’s only now being seen of importance within the academic community. Everyone knows alpha and beta, but if you want to group behavior, there are 6 generally accepted, Greek named, behavior types. Sigma is the rarest, and many can be mistaken for it, but very few are truly it. Now ! Why do I explain this ? Because an intelligent conversation can only come to fruition if the two parties truly understand each other. I could say “ Red “. You could identify red as blue, so immediately the conversation is null and void, bound too lead to misunderstandings.
 

Latest posts

Back
Top